20% off Sterling Silver, 10% off Gold and Diamonds, 10% off Engagement Rings, and 20% off Wedding Bands.
The short answer
A matching pair is designed as one idea in two rings. The band echoes the engagement ring's metal, width and finish, and it is shaped to sit against it rather than beside it with a gap. We design both, so you see the two together before either is made — and there is no obligation to buy.
- Match the metal, the width, the profile and the finish — not necessarily the design.
- Decide the band while the engagement ring is still being designed, if you can.
- A low-set or wide engagement ring needs a shaped band; a higher setting leaves room for a straight one.
- A band can be made to fit a ring you already own.
What makes two rings look like a pair
Matching rings share a language, not a design. What the eye reads as a set is the metal in the same tone, the band at a similar width, the profile shaped the same way, and the finish carried across both. Within that, the engagement ring can be a diamond halo and the band a plain court, and they will still look chosen together.
This is why ordering a band as an afterthought tends to disappoint. A band that is right on its own can look wrong beside the ring it was bought for, and the reason is usually proportion rather than style.
Start with the engagement ring's setting
The engagement ring decides what the band can be, because the band has to meet it. Two things matter: how high the setting sits above the finger, and how wide the ring is at the base.
A high setting leaves a clear run of finger under the stone, so a straight band slides underneath and sits flush. A low setting or a wide, spreading head leaves no room, and a straight band stops short with a visible gap. That gap is not a fault in either ring; it is the two profiles disagreeing.
If both rings are being made, say so at the first consultation. Designing them together is easier than fitting one to the other afterwards. More on the process in our bespoke jewellery design service.
How the band sits against the ring
There are three practical answers, and the right one depends on the ring you have.
| Band style | What it does | Suits |
|---|---|---|
| Straight | A plain band that meets the ring at the base | A high setting with clear space under the stone |
| Shaped or curved | Contoured to follow the outline of the setting | Low settings, halos, clusters, wide heads |
| Notched | Straight in the hand, with a cut-out at the ring's base | A ring with a raised base but little side clearance |
A shaped band is not a compromise. It is made to the ring's own outline, so the two sit together as one piece of jewellery, and the curve only exists on the side that faces the engagement ring — the outer edge stays straight.
Watch out: a straight band chosen without measuring the ring will not sit flush, and reshaping it afterwards removes metal. Have the ring measured before the band is chosen.
One metal or two
Both rings in the same metal is the simplest route and the most durable, because two rings worn on the same finger rub against each other constantly. Platinum against platinum wears evenly. Platinum against gold wears the gold faster, because platinum is the denser of the two.
Mixing is still worth doing where the look asks for it, and it works best when the two metals are deliberately different rather than nearly the same. A yellow gold band beside a white gold engagement ring reads as a choice; a white gold band beside a platinum ring reads as a mismatch, because the two whites are not the same colour.
A note on white gold: it is finished with rhodium to reach its bright white, and it will need replating from time to time to stay that colour, while platinum keeps its own. Neither is better; they age differently. Our wedding rings and bespoke bands page sets out the options we make.
Width, and why it matters more than people expect
A band's width is judged against the engagement ring, not on its own. A band noticeably narrower than the ring looks thin beside it; one noticeably wider pulls attention away from the stone. Matching the two, or coming within a fraction of a millimetre, is what makes a pair look settled.
Width also changes how the band feels. A wider band has more metal in contact with the finger and sits more firmly, which some people prefer and others find heavy. There is no correct answer, but it is worth trying both before deciding.
A band for a ring you already own
A ring does not have to be new for a band to be made for it. Bring the engagement ring in and we take its outline, then shape the band to it, so the pair sit together as though they were made at the same time.
If the ring is an inherited piece or a setting that has seen wear, this is also the moment to look at it properly. Claws thin, settings loosen, and a band fitted to a ring that needs attention is a job done twice. Our remodelling service covers what can be rebuilt around an existing stone, and our repair service covers the smaller work.
Seeing the two together before either is made
Designs are shown in 3D within 24 hours, which matters more for a pair than for a single ring: you see the two together, from the front and from the side, and the gap or the fit becomes obvious before any metal is cut. You can start shaping an idea in the online ring builder, or come in and see the showroom on South Street.
Consultations run in the showroom, by home visit, or remotely, and nothing needs deciding in advance. If the design is not right, we redraw it; that is what the drawings are for. Purchases come with 30-day returns.
Questions we are asked
Do both rings have to be the same metal?
No, and mixed metals can look deliberate and good. What matters is that the difference reads as a choice rather than an accident, so keep the tones clearly apart if you mix them. Two rings in the same metal will simply wear against each other more evenly.
Can you make a band to fit a ring I already have?
Yes. We take the outline of the engagement ring and shape the band to it. It is worth bringing the ring with you rather than a photograph, because the fit depends on the profile in the hand.
Should we choose the wedding band at the same time as the engagement ring?
It is easier. The engagement ring settles the metal and the setting height, and the band follows from both. If the band is chosen later, it can still be shaped to the ring, but designing the pair together usually saves a redraw.
Can a band be added years later and still match?
Yes. Metal, width and profile can all be matched to an existing ring. A ring worn for years carries small marks that a new band will not, and the two settle together as the newer one is worn.
Tell us what you have in mind, and we will draw the pair together and show you how they sit. There is no obligation to buy.